Excel MRL

An electric traction-gearless elevator built for low-to-mid-rise buildings

The MRL solution is the perfect choice when you need to meet space restrictions and safety.

The control room next to the hoist way allow you give service to all your building floors without a bulkhead problem.
The gearless motor gives the user a smooth and low noise ride. The energy savings and quality standards make this option one of the strongest mobility options in the elevator market.

Excel MRL are able to meet all the quality targets and give you an endless possibilities in finishes. Contact our sales team and find the perfect solution for your building.




  • Specifications

    Capacity: 2100lbs, 2500lbs, 3000lbs, 3500lbs, 4000lbs, 4500lbs.
    Speed: 200 fpm
    Stops: Up to 12 stops
    Maximum Travel: 110ft
    Pit: 5’6″
    Power Supply: 220V-440V-Three phases.
    Drive System: VVF
    Control System: Microprocessor Controller | Fully Automatic System
    Code Compliance: ASME A17.1 National Code, ASME A17.1-2002, Local Code.
    Cab Size: 2100 lbs: 68″ x 51″ | 2500 lbs: 80″ x 51″ |3000 lbs: 80″ x 57″ | 3500 lbs: 80″ x 65″ | 4000 lbs: 92″ x 65″
    Cab Configurations: Front, Rear

  • Standard Features

    VVF for smooth and comfortable ride.
    Dot matrix car Indicator.
    Illuminated halo push buttons
    Automatic fan and cab light
    Landing call stations with indicator

  • Optional Features

    Graphic car indicator
    Custom car finishes
    Voice announcement

  • Safety Features

    Automatic bidirectional floor leveling
    Emergency Back up
    Emergency stop and alarm
    Fully automatic doors
    Uncontrolled movement
    Door interlocks
    UL certified components

  • Work by Others

    The following requirements must be met before installations is completed and are not included in the elevator contract.
    Owner or general contractor to provide the following according to A17.1 Code unless local code is more stringent.

    1. Plump within 1” and properly ventilated hoistway according to code and sizes shown.
    2. Adequate supports for buffers and rail guide brackets. When maximum spacing is exceeded, rail supports shall be provided at owner’s expense.
    3. Hoistway barricades (all cutting and patching to install entrances, sill and hall fixtures.. Also refer to entrances drawing for suitable sill support, recess and grouting.
    4. Projections of 2” or more shall be beveled at angle not less than 75 from horizontal.
    5. Hoist beam insert or hook to be installed at to of the hoistway in the center of the car and rails.
    6. Motor base beam and counterweight beam according to shop drawings.
    7. Overhead niches according to shop drawings.
    8. Speed governor access and a 42”x42” motor access.
    9. A temporary work platform is required for installation. It is to be constructed at the top floor of each elevator. It must comply with applicable governing codes and regulations. The platform must be securely fastened to the building structure. Erection, maintenance, and removal are by others.
    10. Floor recess of full width of the hoistway at all entrances for sills to the size shown. Grout by others.
    11. Where possible entrances walls to be constructed after door frames and sills are installed. If rough openings are to be used then rough openings must be 8” on each side.
    12. Guide rail brackets must be installed before fireproofing the hoistway.
    13. Sleeves in the hoistway walls for the wiring duct for each car.
    14. Door bucks and tracking sills, to be set plumb above each other and square with hoistway. In tile, concrete block or similar walls, side members must extend from sill to beam above. Where front and rear openings, the dimensions between door frames must be maintained.
    15. Guide rail support locations must be steel, brick, concrete block. If used, inserts are supplied and installed by others, in shown locations as walls being erected. If rail brackets are attached to steel beams, fire proofing must be applied after rail brackets are in place, Steel beams size & location is specified by the elevator contractor, steel beams are furnished and erected by others.
    16. A legal dry pit with a reinforced floor to sustain vertical forces as shown. At impact all forces shown must be doubled.
    17. A pit ladder for each car of non combustible material and extends from the pit floor to 48” above the sill of the bottom landing is required.
    18. Light, light switch and duplex “GFI” electric outlet, in the pit and overhead. The light switch accessible from the bottom and top landing opening.
    19. Pit ladder shall be provided when required.

    20. A legal lighted and ventilated control room at top floor with access and controlled temperature maintained between 60-95 deg F. The control room door should be locked and secured against unauthorized access according to the code. It should be self closing, locking, and openable from inside without a key.
    21. 42” minimum clear space is required in front of control space door and top hoistway entrance to service barriers. Additional hallway width may be required subject to local buildings, fire and ADA codes.
    22. Door must be capable of opening 180 degrees for access to control space.
    23. Light and switch in the control room with switch located adjacent to the access door.
    24. A duplex “GFI” electric outlet must be provided.

    25. A fused disconnect switch for each car wiring to each elevator’s motor starter control. Disconnected means shall be disconnect all electrical power from the power surce(s. including emergency power when required.
    26. A suitable 25A 110Vac disconnect switch for car light service located in the control room and connected to the terminals in the control panel.
    27. Heat and smoke sensors to be located at each elevator lobby with necessary wiring to each car control panel.
    28. A telephone in each elevator car and its wiring from the building service to the elevator’s control panel.
    29. A separate 25A 110Vac fused service with ground(Supplied thru automatic emergency lighting supply if available. connected to elevator signal controller for car lighting.


    30. A safe and dry room to store the elevator’s equipment and tools required for construction.
    31. Necessary power for installing the elevator free of charge.
    32. Any other equipment(s. or source(s., not specified above, beyond the normal scope of supply of the elevator contractor and is necessary for the elevator(s. installations.

technical specifications library

The Fabian USA design advantage:


Our broad array of cab and floor finishes complements your home’s décor!

Our steel and glass hoistways, suitable for both interior and exterior placement, can enhance the architecture of your structure.

From historic preservation, to branded retail designs, you can see some of our unique installations here!